How to Hook Up a Water Line to a Refrigerator From the Sink
The kit comes with a self tapping valve that will allow the hose to hook up without any tools. Can I get my ice maker to dump ice without hooking up a water line? It already has the hook up line in back of it. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. Pro Tip Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking.
If the joists are laid in the same direction the hose needs to go, then it is simply secured in place with plastic loops against the side of one joist. When it comes to home repairs, why is it best to hire a professional rather than looking up YouTube videos to do it yourself? If so, your job is very easy. If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use.
And for the distance you are dealing with, you may need to buy the needed length of flex hose separately, and discard the too short section in the kit. Leave the excess water line behind the refrigerator. Tile a homemade shower stall? Should I pour ammonia down a sink drain, then follow with bleach to unclog it? Everything You Need to Know Browse a full list of topics found on the site, dating a morbidly obese from accessories to mudrooms to wreaths.
Repeat this process with the water inlet plug and the mounting hole plugs located on the side of the freezer wall. The cold water line to the washer will work fine. Turn on the cold water faucet to drain any water left in the supply line.
She writes mainly home improvement, health and travel articles for various online publications. The sink is in the other side of the kitchen and going through the floor is not an option because I have tile. Run the new supply tube to the back of the refrigerator. Can I hook it up to the water line from the clothes washer? Install the Factory Fill Tube The next step is to install the factory fill tube.
Turn the cold water supply valve on beneath the sink. Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. Now that the water's off, free dating site install the new valve for the icemaker water line. Install the Icemaker With all the work done on the back side of the freezer it's time to install the icemaker unit itself. Why is it recommended that you hook up an ice maker to hot water line?
- If you have any more questions give me a holler.
- It simply clamps on to the cold water pipe and presses a hole in it for the fridge water.
- Or do I have to tear walls?
- Mount the Solenoid Valve The first part of the icemaker kit is called the solenoid valve.
- Insert the new water line into the opening on the tee.
How to Install an Icemaker
Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up. It's a very easy valve to use. They come in various sizes to suit whatever situation you have. Tighten the connections slightly if you see a leak. If the refrigerator has a water dispenser, man older flush out several gallons to purge the line of all the air.
Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first. Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections. The water line kits are sold at Home Depot, Lowes, Manard's, and the like.
How do i hook up my water line to my ice maker
Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. You can use any hrd cold line. The first part of the icemaker kit is called the solenoid valve.
Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment. Shut off the water at the valve that controls the cold-water supply pipe to the faucet. The closest water line is my clothes washer water pipe. You are not talking about the hot and cold hoses are you?
So I always just make a trip to the hardware store and get the fittings necessary to install a regular valve for this. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Turn the supply line on once again.
Slip the remaining compression nut and ferrule over the refrigerator end of the new water line. If I am shipping several house hold items, long distance. Watch for leaks at all the connections.
How to Install a Water Line for a Refrigerator
- Using the plastic tubing provided with the kit, screw the plastic fitting to the water outlet on the bottom of the solenoid valve.
- First, locate the shutoff valve under the kitchen sink where you want to connect the new water line.
- She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.
You are being redirected
My townhome is an old construction and I don't have a water hook up behind my fridge. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench. When the hose reaches the area in the basement, just under the sink, a cold water pipe probably half inch will be easily accessible. Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking.
Tighten the connection just slightly more than hand-tight, using pliers. Slip the compression nut that came with the kit over the newly installed supply line. Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator.
Drill a hole behind the refrigerator, and then one underneath the sink. Turn the cold water on the supply line clockwise to close it. Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more. Related Questions We just bought a refrigerater with an ice maker and water maker.